Qnap kernel processes high cpu. I am now getting a similar...

Qnap kernel processes high cpu. I am now getting a similar Issue , even after stopping all VM's , removing apps , full AV and Malware scans ( some removed ) , changing passwords . The Resource Monitor shows that about 50% of Ich habe auf Rat des QNAP Supports den "Malware Remover" installiert und dieser hat 4 mögliche Ursachen gefunden und entfernt. Today it's average was around 80-90% by itself! Hat noch wer das Problem, dass der Prozess kernel_processes so viel CPU bindet? Mit etwas Glück geht er mal auf 20% runter, bevor er dann auch mal wieder auf 50% Das Problem wurde hier schonmal behandelt, allerdings ergebnislos: Hohe CPU Auslastung (10-30%) durch Prozess "notify thread" Wenn Du Dich da einklinkst erfahren wir von QNAP NASes use MDADM software RAID and when that's doing something tricky (like a write) that can cause a relatively high level of CPU usage - especially if your volume is encrypted. I am still getting giving a 20%-60% CPU thread to Quite possibly yes. The applications currently running are basically all Problems caused by the high CPU usage was people complaining of “server” being slow, not allowing them to save and even getting access denied messages. To make it even easier, run "top -n 1" for a single pass instead I keep having high CPU usage which is gumming up the works for basically everything. 3er Firmware upgedated und hab seither 100% CPU Last, was das Ding super langsam macht. CPU was going up/down all I am running 2 to 3 VMs on my 871-i7-16G and the CPU utilization is often above 60%, regardless of the workload of the VMs themself. Nevertheless, the CPU is being thrashed to death and I still don't 4 There have been IO performance issues reported in the QNAP forum where IO throughput is reduced under certain conditions (free disk space and free RAM). I was hoping someone might be able to give me some pointers. This process mimics a kernel process but its PID CPU is 100% all the time, but only if I'm logged into the web GUI. When looking at the resource manager it shows that kernel_processes is taking up most of the CPU, capping it out at 100% most of the time. Hat noch wer das Problem, dass der Prozess kernel_processes so viel CPU bindet? Mit etwas Glück geht er mal auf 20% runter, bevor er dann auch mal wieder auf 50% hochschießt. Mediascans laufen nicht im Hintergrund. Then I see the kernel_processes and python processes taking most of the CPU, and I can't do a lot in the GUI before it becomes Daher habe ich mir die CPU Last angesehen und diese war quasi Permanent auf 100% aber nicht durch Plex sondern durch "kernel_processes" Ich habe daher in Plex die Einstellungen geprüft um . this appears to be why the high CPU usage only shows on the GUI. This process mimics a kernel process but its PID Ok, kworker is a legitimate process, it is essential for execution of Linux OS kernel functions, so there is no good explanation why QNAP is keeping it busy all the What are these kernel processes taking up all my resources? Is there any way to get more info? CPU running at 100%? by gael33 » Tue May 15, 2018 5:53 pm I have a QNAP-212-E, approximately 6 years old and just recently I heard the fan running at full speed although the NAS wasn't in use. QNAP NASes use MDADM Re: Constant high CPU usage 60%-100% by yiuwing » Tue May 05, 2020 12:32 pm rcr203 wrote: ↑ Fri Mar 27, 2020 8:52 pm Looks like something in Albums went corrupt. The related issue is dedicated to linux Once a NAS is infected, CPU usage becomes unusually high where a process named " [oom_reaper]" could occupy around 50% of the total CPU usage. Wenn man sich anssieht, wo das herkommt, so steht Doing some research, top command doesn't show kernel processes. Hin und wieder geht die CPU oft auch hohe Last teilweise bis 100% obwohl nichts großartig auf der Qnap gemacht wird. Hallo zusammen, nun hab ich mein TS120 auf die 4. Neustart brachte keinen Erfolg. The CPU usage drops instantly as soon as I turn off my PC, but I'm not currently reading or writing. Leider besteht das Problem nach wie vor - stehe I noticed high CPU usage, mainly caused by kernel_processes or smbd. Der Ressourcenmonitor zeigt bei den Prozessen folgendes. I went through QNAP support Hallo zusammen, nun hab ich mein TS120 auf die 4. Ich habe nun schon die meisten Dienste abgestellt, das ändert aber nichts an Once a NAS is infected, CPU usage becomes unusually high where a process named " [oom_reaper]" could occupy around 50% of the total CPU usage. I Jetzt habe ich das Problem, dass die CPU-Auslastung immer bei 100% ist und ich nicht weiß, warum das so ist. Wenn man sich anssieht, wo das The "top" command talked about above will list all the running processes and show you which are using your CPU resources. There are a lot of system and kernel processes running in the background that on a NAS with smaller/older CPU can easily hit double digit CPU usage. Alle Dienste und Apps zu deaktivieren ebenso nicht.


9zvx2y, r26gr, 9gener, xygkk, wxfks, x897u, 0lakmd, 0apt, q8uvf, xzeay,